Yale SmartHome Alarm series Especificações Página 21
- Página / 32
- Índice
- RESOLUÇÃO DE PROBLEMAS
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
21
Using your keypad
•ThekeypadcanbeusedtoAwayArmandHome
Arm the system using the buttons as shown.
•Thesystemisdisarmedbypressingthedisarm
button followed by any user code, similar to using
the control unit keypad.
•Anemergencyalarmcanbeactivatedbypressing
the panic A and B buttons simultaneously.
Deactivate you panic event by pressing disarm
button followed by any user code.
•Thekeypadusesthesameuserpincodes
programmed into the control unit for disarming.
•Toextendtheexittime,pressthearmorhome
arm button once more on the keypad.
•Ifthereisasystemfault.youwillneedtopressthe
arm/home arm button for a second time to “force
arm” the system.
Using your smoke detector
Smoke Detection
When smoke is detected the device will activate for
a minimum of 10 seconds with a two tone alarm and
flashing LED for a local fire alarm. The detector will
send a radio signal to the control unit for activating a
system fire alarm.
•Pressingthetestbuttonwheninanalarm
condition will silence the alarm for 10 minutes. It
will automatically resume smoke detection again
after this period.
•Ifthesmokedensityisstilloverthealarm
threshold, then the smoke detector will remain in
an alarm condition and it will repeat the local fire
alarm with a radio fire alarm signal to the control
unit.
Testing
•Smokedetectortestingshouldbedoneona
regular monthly basis. Pressing the test button will
make the LED flash, the audible sounder chime
and will send a radio test signal to the control unit
when the button is released. If nothing happens
after pressing the test button, it indicates the
batteries will need changing.
Recalibration
•Thesmokedetectormightneedrecalibratingafter
time to ensure it is working at its optimum. This is
done by pressing and holding the test button until
the LED flashes and beeps after 10 seconds. The
detector will then start its self calibration routine.
Using your Help Button
Activate an Alarm
•Pressandholdtheredbuttonforatleast3
seconds. The LED will light momentarily and the
alarm will be activated.
Silence an Alarm
•Pressandholddowntheredbuttonfor10
seconds. The LED will light momentarily for a
second time and the alarm will be silenced.
•Pleasenotethatsilencingthealarmwiththehelp
button does not reset the system. If the alarm is
armed prior to activation, the system will re-arm
after being silenced with the help button.
•Thesystemwillrequirearesetatthecontrolunit
after being silenced with the help button.
- Easy Fit Touch Screen 1
- Location planning 2
- Text Display 3
- Unpack all the parts 4
- Learn/Test 5
- First Time Easy Set-up 6
- Error Condition 7
- (Upon selecting Exit setup) 7
- Control Unit Mounting 8
- Mounting the Keypad: 9
- Mounting the Door Contact 9
- Mounting the Help button 9
- Mounting the Smoke Detector 9
- Press test on 11
- Add Devices 12
- Zone Type List 12
- Edit Devices 13
- Remove Device 13
- Program Siren 13
- Adv. Settings 14
- Tel. Settings 16
- Using the System 17
- Stop the Alarm and Alarm 18
- Enabling the system tamper 19
- Preparation 20
- Adding accessories to your 20
- Using your keyfob 20
- Using your smoke detector 21
- Using your Help Button 21
- Changing the Batteries 22
- Keyfob battery change 23
- Keypad battery change 23
- Help button battery change 23
- Smoke detector battery change 23
- Troubleshooting 24
- Complete Reset Procedure 25
- Partial Reset Procedure 25
- Alarm sensor response table 27
- Specifications 28
- On behalf of ASSA ABLOY Ltd 29
- Installation Notes: 30
- 2 Year Guarantee 32
- Statement 32
(6 páginas)
Comentários a estes Manuais